Duration: 8 weeksElectrical Power System Concepts & Technology
Fundamentals of generation, transmission, distribution, and modern grid technology for engineers and technicians.
Programs
All Training Programs
38 courses across 11 specializations
Duration: 8 weeksFundamentals of generation, transmission, distribution, and modern grid technology for engineers and technicians.
Duration: 6 weeksLow-voltage system design, load calculations, cable sizing, and panel layout per international standards.
Duration: 5 weeksSelection, operation, and maintenance of LV switchgear, MCCs, and protection devices.
Duration: 4 weeksTesting procedures, diagnostics, and maintenance standards for power system equipment.
Duration: 10 weeksRelay coordination, fault analysis, protection schemes, and practical substation applications.
Duration: 4 weeksPower system modeling, load flow, short-circuit, and protection studies using ETAP software.
Duration: 4 weeksElectrical drafting, schematic diagrams, and panel layouts with AutoCAD for engineering projects.
Duration: 4 weeksMaterials, mix design, testing methods, and quality control for structural concrete.
Duration: 3 weeksOn-site placement, curing, formwork, and supervision of concrete works.
Duration: 4 weeksQuantity surveying, BOQ preparation, and cost control for civil projects.
Duration: 4 weeksSelection, operation, performance curves, and maintenance of centrifugal pumps.
Duration: 5 weeksHVAC system design, installation principles, and maintenance for commercial and industrial buildings.
Duration: 4 weeksWater supply, drainage systems, pipe sizing, and plumbing codes in building services.
Duration: 4 weeksFire detection, suppression systems, and NFPA-aligned design for life safety.
Duration: 4 weeksPipeline integrity assessment, inspection methods, and maintenance planning for oil & gas infrastructure.
Duration: 5 weeksWorkplace HSE policies, risk assessment, incident investigation, and compliance.
Duration: 4 weeksDesign and deploy IP CCTV over LAN: camera selection, PoE switching, cabling, NVR/VMS setup, VLANs for surveillance traffic, remote viewing, and network troubleshooting.
Duration: 6 weeksNetworking fundamentals aligned with CCNA: IP addressing, switching, routing, VLANs, and hands-on labs for enterprise and surveillance networks.
Duration: 4 weeksOSI/TCP-IP models, Ethernet, IP addressing & subnetting, switches & routers, Wi‑Fi basics, and practical labs for building small reliable networks.
Duration: 6 weeksPLC programming, ladder logic, I/O configuration, and troubleshooting on Allen Bradley platforms.
Duration: 5 weeksSCADA architecture, HMI development, data logging, and industrial automation integration.
Duration: 5 weeksLadder logic fundamentals, timers, counters, and hands-on wiring labs for industrial control.
Duration: 6 weeksFoundations of classic control, process instrumentation, and variable frequency drives.
Duration: 6 weeksSiemens PLC programming from basics to advanced using TIA Portal.
Duration: 6 weeksIntegrated Siemens automation workflows using SIMATIC Manager.
Duration: 6 weeksBroad coverage of industrial control architectures, sensors, actuators, and system design.
Duration: 6 weeksIntroductory ABB Freelance DCS engineering for process industries.
Duration: 4 weeksDrive-test fundamentals for 2G/3G networks using TEMS Investigation workflows.
Duration: 4 weeksGSM radio planning concepts with practical exposure to Atoll planning software.
Duration: 4 weeksOptimization and KPI monitoring practices for GSM radio networks.
Duration: 4 weeksLTE architecture, air interface concepts, and network technology fundamentals.
Duration: 4 weeksTransmission media and technologies used in modern telecom backhaul and transport.
Duration: 4 weeksEssential core-network nodes, signaling concepts, and service flows for 2G/3G.
Duration: 4 weeksPlanning principles for 3G radio networks covering coverage, capacity, and quality.
Duration: 8 weeksTechnical vocabulary, report writing, and communication skills for engineering workplaces.
Duration: 6 weeksCore HSE principles, hazard identification, PPE, and preparation for recognized HSE credentials.
Duration: 4 weeksProject management frameworks, processes, and exam-oriented practice aligned with PMP preparation.
Duration: 4 weeksBudgeting, financial analysis, project costing, and decision-making for managers and engineers.